This dataset is produced for the Government of Alberta and is available to the general public. Note that the distribution contact is different for the general public than for Government of Alberta ministries. Please consult the Distribution Information of this metadata for the appropriate contact to acquire this dataset. The National Topographic System of Canada (NTS) is a national mapping reference grid defined by Natural Resources Canada (NRCan) that is based on degrees of latitude and longitude. Starting at the Prime Meridian and at the equator, the 1:250 000 grid is formed by intersecting every degree of the meridians with every two degrees of parallels. Each polygon in the grid is designated with a two digit number and a single letter (Example 83H). The province of Alberta is covered by 45 complete and 17 partially complete 1:250 000 NTS blocks.

This dataset is a digital representation of Saskatchewan's Quaternary geology at 1:250 000 scale.This dataset is a 1:250,000 scale Quaternary geology map series showing surficial terrain deposits classified by depositional environment and geomophology in the Province of Saskatchewan. Mapping of this dataset was compiled by Agriculture and Agri-Food Canada and Prairie Farm Rehabilitation Administration (PFRA), and merged by the Government of Saskatchewan. **Please Note – All published Saskatchewan Geological Survey datasets, including those available through the Saskatchewan Mining and Petroleum GeoAtlas, are sourced from the Enterprise GIS Data Warehouse. They are therefore identical and share the same refresh schedule.

For the purpose of this dataset, an Indigenous government or group refers to both elected Indigenous governments, and entities that are formally designated to represent individual Indigenous rights-holders but does not include Indigenous advocacy organizations such as the Assembly of First Nations, the Council of Yukon First Nations or boards, committees or councils established to represent community interests.For the purpose of this data set, Indigenous governments can include but is not limited to a Yukon First Nation or a transboundary Indigenous government. A “Yukon First Nation” refers to a First Nation that is included in the definition of “Yukon First Nation” in the Umbrella Final Agreement, and includes: Carcross/Tagish First Nation, Champagne and Aishihik First Nations, Kluane First Nation, Kwanlin Dün First Nation, Liard First Nation (Kaska Nation), Little Salmon/Carmacks First Nation, First Nation of Nacho Nyak Dun, Ross River Dena Council (Kaska Nation), Selkirk First Nation, Ta’an Kwach’an Council, Teslin Tlingit Council, Tr’ondëk Hwëch’in (identified in the Umbrella Final Agreement as “Dawson First Nation”), Vuntut Gwitchin First Nation, and White River First Nation.A transboundary Indigenous government refers to an Indigenous government that is based outside of the Yukon, and includes: Acho Dene Koe First Nation, Dease River First Nation (Kaska Nation), Kwadacha Nation (Kaska Nation), Gwich’in Tribal Council, Tetlit Gwich’in Council, Inuvialuit Regional Corporation, Inuvialuit Game Council, Tahltan Central Government, Taku River Tlingit First Nation, and Pehdzeh Ki First Nation.For this dataset, a boundary is a depiction of a division between different geographic regions associated with an Indigenous government (e.g., a full or partial periphery of a “traditional territory”). A boundary can include, but is not limited to, a “traditional territory” or “Traditional Territory”. For this dataset, a traditional territory or Traditional Territory is a geographic area where a group of Indigenous Peoples holds or asserts Indigenous rights, and which may be established by a treaty or confirmed in a court ruling.The term “Traditional Territory” (capitalized) is defined in the Umbrella Final Agreement and specifically refers to the territories identified in the maps submitted by each Yukon First Nation during the negotiation of that agreement and each Yukon First Nation final agreement. Some Indigenous governments and groups or the text of their treaty agreements do not use the term “traditional territory”. For example, the Gwich’in Tribal Council’s boundary in Yukon is more accurately described as Tetlit Gwich'in Yukon Lands and the Inuvialuit Regional Corporation’s boundary in Yukon is more accurately described as the Inuvialuit Settlement Region. Historical use and occupancy information can be used to understand assertions of rights within a traditional territory that has not been formally established.Distributed from [GeoYukon](https://yukon.ca/geoyukon) by the [Government of Yukon](https://yukon.ca/maps). Discover more digital map data and interactive maps from Yukon’s digital map data collection.For more information: [geomatics.help@yukon.ca](mailto:geomatics.help@yukon.ca)

The Yukon Geological Survey (YGS) has compiled over 195 surficial geology maps into a standardized GIS format, providing approximately 80% coverage of the territory. The maps range in scales from 1:250,000 to 1:10,000 with spatial overlap between scales. The original maps were produced by various agencies, including the Geological Survey of Canada, YGS, Yukon Government, universities, and the City of Whitehorse.All original feature descriptions have been preserved and also converted to standardized values using the Yukon terrain classification system. The compilation includes 4 GIS datasets and supporting documents available for download via [YGS integrated data system](https://data.geology.gov.yk.ca/Compilation/33) (YGSIDS) or GeoYukon. A .lyr file is [provided](https://data.geology.gov.yk.ca/Compilation/33) to symbolize feature classes and differentiate overlapping maps at different scales. Additionally, there is a surficial geology map index.The polygon attributes captured include surficial material, texture, age, surface expression, and geomorphological processes.Line features include geological contacts, glacial limits, glacial landforms (cirques, arêtes, eskers, meltwater channels, moraines), and non-glacial landforms (faults, lineaments, landslides, escarpments).Point features include field station, fossil and sample locations, glacial landforms (erratics, kames, kettles, drumlins, flutings), permafrost features (pingos, palsas, patterned ground, thermokarst depressions), and other non-glacial landforms (landslides, tors).The map index provides information on each map publication such as author, map title, map scale, publisher.These data are valuable for land-use applications in the territory, including: mineral and placer exploration, geotechnical engineering, infrastructure planning, granular resource assessments, permafrost modeling, agricultural assessments, forest management, and biophysical or ecological land classification.Distributed from [GeoYukon](https://yukon.ca/geoyukon) by the [Government of Yukon](https://yukon.ca/maps) . Discover more digital map data and interactive maps from Yukon's digital map data collection.For more information: [geomatics.help@yukon.ca](mailto:geomatics.help@yukon.ca)

The Yukon Geological Survey (YGS) has compiled over 195 surficial geology maps into a standardized GIS format, providing approximately 80% coverage of the territory. The maps range in scales from 1:250,000 to 1:10,000 with spatial overlap between scales. The original maps were produced by various agencies, including the Geological Survey of Canada, YGS, Yukon Government, universities, and the City of Whitehorse.All original feature descriptions have been preserved and also converted to standardized values using the Yukon terrain classification system. The compilation includes 4 GIS datasets and supporting documents available for download via [YGS integrated data system](https://data.geology.gov.yk.ca/Compilation/33) (YGSIDS) or GeoYukon. A .lyr file is [provided](https://data.geology.gov.yk.ca/Compilation/33) to symbolize feature classes and differentiate overlapping maps at different scales. Additionally, there is a surficial geology map index.The polygon attributes captured include surficial material, texture, age, surface expression, and geomorphological processes.Line features include geological contacts, glacial limits, glacial landforms (cirques, arêtes, eskers, meltwater channels, moraines), and non-glacial landforms (faults, lineaments, landslides, escarpments).Point features include field station, fossil and sample locations, glacial landforms (erratics, kames, kettles, drumlins, flutings), permafrost features (pingos, palsas, patterned ground, thermokarst depressions), and other non-glacial landforms (landslides, tors).The map index provides information on each map publication such as author, map title, map scale, publisher.These data are valuable for land-use applications in the territory, including: mineral and placer exploration, geotechnical engineering, infrastructure planning, granular resource assessments, permafrost modeling, agricultural assessments, forest management, and biophysical or ecological land classification.Distributed from [GeoYukon](https://yukon.ca/geoyukon) by the [Government of Yukon](https://yukon.ca/maps) . Discover more digital map data and interactive maps from Yukon's digital map data collection.For more information: [geomatics.help@yukon.ca](mailto:geomatics.help@yukon.ca)

This Shaded Relief Image has a resolution of 300 meters and was derived from the "Yukon 90m Shaded Relief" from Environment Yukon, the "Canada 3D" elevation model from Natural Resources Canada, and the United States Geological Survey "1:250k DEM of Alaska".Distributed from [GeoYukon](https://yukon.ca/geoyukon) by the [Government of Yukon](https://yukon.ca/maps) . Discover more digital map data and interactive maps from Yukon's digital map data collection.For more information: [geomatics.help@yukon.ca](mailto:geomatics.help@yukon.ca)

Regional stream sediment geochemical data compilationNovember 2020Release notesThe regional stream sediment geochemical data compilation comprises data for more than 30 000 samples across Yukon. This compilation updates the work of Héon (2003). This new compilation includes results from the reanalysis of more than 24 000 samples; inductively coupled plasma mass spectrometry (ICPMS) analysis provides upgraded detection limits and a broader range of elements relative to previous analytical data. In addition to analytical data, efforts have been made to improve sample location accuracy. The data in this release are organized by analytical method with the geodatabase having six feature classes:1. RGS_SITE_WATER - site specific physiography and water quality data. These data are unchanged from the original releases. 2. RGS_HEON - the same data as released in Héon (2003) with minor updates to sample location. 3. RGS_AAS - all samples analyzed by atomic absorption spectrometry. Most of these data are superseded by INAA and ICPMS data. 4. RGS_INAA - all samples analyzed by instrumental neutron activation analysis (INAA) and fire assay-neutron activation (FA-NA) analysis. 5. RGS_ICPMS - all samples analyzed by inductively coupled plasma mass spectrometry (ICPMS). 6. RGS_All - includes all AAS, INAA and ICPMS data. Collection of stream sediment samples in Yukon began in 1976 and ended in 2006. Three analytical methods have been used to analyze the minus 0.177 mm fraction (-80 mesh) of these samples: AAS, INNA (and FA-NA) and ICPMS. A simple description of each method is given below.For atomic absorption spectrometry (AAS) a 1 g aliquot is 'partially digested' using Lefort aqua regia or concentrated hot nitric acid. The digestion product is analyzed using an atomic absorption spectrometer. Oxide and silicate minerals are partially digested while some sulphide minerals are erratically volatilized. This means that AAS cannot be used to obtain accurate REE, Ta, Nb, As, Sb, Sn, Hg, Cr, or Au determinations.For instrumental neutron activation analysis ( INAA), aliquots of sieved sediment (the minus 0.177 mm fraction) or milled rock ranging from 5 to 40 g are encapsulated and irradiated in a nuclear reactor before counting the primary gamma radiation induced by the neutron irradiation with a high resolution germanium gamma ray detector. Fire assay-neutron activation (FA-NA) analysis is similar but includes a pre-concentration fire assay step prior to irradiation and analysis. Results for both INAA and FA-NA are similar to those for samples analyses by fusion or other total digestion techniques. Neutron activation detection limits are typically higher than those by acid digestion - ICPMS. Commodity and pathfinder elements such as Au, As, Sb and W have reasonable detection limits by INAA and the data generated are relatively precise.For ICPMS analysis, aliquots of sieved sediment ( the minus 0.177 mm fraction) ranging from 0.5 to 1 g are prepared using a partial digestion technique, typically aqua regia, followed by analysis of dissolution product by ICPMS. Sulphide minerals are completely oxidized and dissolved whereas most oxide and silicate minerals are only partially digested. This means that results produced by partial digestion methods are acceptable for elements such as Ag, As, Mo, Ni, Pb, Sb, Tl, and Zn but values for elements such as Al, Ba, Cr, Fe, P, Sn, Ti, Y, and Zr are likely to not reflect the actual element concentration in a sample. The sample size used for routine RGS sample analysis is too small be representative of Au in the original sample and thus Au by aqua regia digestion - ICPMS has poor precision.Further upgrades to this database are not anticipated. All samples that could be found in the GSC-Ottawa warehouse have been reanalyzed using ICPMS. Any errors or omissions in this database should be reported to the Yukon Geological Survey. Your feedback contributes to improving the accuracy of the geoscience databases for Yukon.Contact: [YGSMinerals@yukon.ca](mailto:YGSMinerals@yukon.ca) ; [geology@yukon.ca](mailto:geology@yukon.ca)Distributed from [GeoYukon](https://yukon.ca/geoyukon) by the [Government of Yukon](https://yukon.ca/maps) . Discover more digital map data and interactive maps from Yukon's digital map data collection.For more information: [geomatics.help@yukon.ca](mailto:geomatics.help@yukon.ca)

Regional stream sediment geochemical data compilationNovember 2020Release notesThe regional stream sediment geochemical data compilation comprises data for more than 30 000 samples across Yukon. This compilation updates the work of Héon (2003). This new compilation includes results from the reanalysis of more than 24 000 samples; inductively coupled plasma mass spectrometry (ICPMS) analysis provides upgraded detection limits and a broader range of elements relative to previous analytical data. In addition to analytical data, efforts have been made to improve sample location accuracy. The data in this release are organized by analytical method with the geodatabase having six feature classes:1. RGS_SITE_WATER - site specific physiography and water quality data. These data are unchanged from the original releases. 2. RGS_HEON - the same data as released in Héon (2003) with minor updates to sample location. 3. RGS_AAS - all samples analyzed by atomic absorption spectrometry. Most of these data are superseded by INAA and ICPMS data. 4. RGS_INAA - all samples analyzed by instrumental neutron activation analysis (INAA) and fire assay-neutron activation (FA-NA) analysis. 5. RGS_ICPMS - all samples analyzed by inductively coupled plasma mass spectrometry (ICPMS). 6. RGS_All - includes all AAS, INAA and ICPMS data. Collection of stream sediment samples in Yukon began in 1976 and ended in 2006. Three analytical methods have been used to analyze the minus 0.177 mm fraction (-80 mesh) of these samples: AAS, INNA (and FA-NA) and ICPMS. A simple description of each method is given below.For atomic absorption spectrometry (AAS) a 1 g aliquot is 'partially digested' using Lefort aqua regia or concentrated hot nitric acid. The digestion product is analyzed using an atomic absorption spectrometer. Oxide and silicate minerals are partially digested while some sulphide minerals are erratically volatilized. This means that AAS cannot be used to obtain accurate REE, Ta, Nb, As, Sb, Sn, Hg, Cr, or Au determinations.For instrumental neutron activation analysis ( INAA), aliquots of sieved sediment (the minus 0.177 mm fraction) or milled rock ranging from 5 to 40 g are encapsulated and irradiated in a nuclear reactor before counting the primary gamma radiation induced by the neutron irradiation with a high resolution germanium gamma ray detector. Fire assay-neutron activation (FA-NA) analysis is similar but includes a pre-concentration fire assay step prior to irradiation and analysis. Results for both INAA and FA-NA are similar to those for samples analyses by fusion or other total digestion techniques. Neutron activation detection limits are typically higher than those by acid digestion - ICPMS. Commodity and pathfinder elements such as Au, As, Sb and W have reasonable detection limits by INAA and the data generated are relatively precise.For ICPMS analysis, aliquots of sieved sediment ( the minus 0.177 mm fraction) ranging from 0.5 to 1 g are prepared using a partial digestion technique, typically aqua regia, followed by analysis of dissolution product by ICPMS. Sulphide minerals are completely oxidized and dissolved whereas most oxide and silicate minerals are only partially digested. This means that results produced by partial digestion methods are acceptable for elements such as Ag, As, Mo, Ni, Pb, Sb, Tl, and Zn but values for elements such as Al, Ba, Cr, Fe, P, Sn, Ti, Y, and Zr are likely to not reflect the actual element concentration in a sample. The sample size used for routine RGS sample analysis is too small be representative of Au in the original sample and thus Au by aqua regia digestion - ICPMS has poor precision.Further upgrades to this database are not anticipated. All samples that could be found in the GSC-Ottawa warehouse have been reanalyzed using ICPMS. Any errors or omissions in this database should be reported to the Yukon Geological Survey. Your feedback contributes to improving the accuracy of the geoscience databases for Yukon.Contact: [YGSMinerals@yukon.ca](mailto:YGSMinerals@yukon.ca) ; [geology@yukon.ca](mailto:geology@yukon.ca)Distributed from [GeoYukon](https://yukon.ca/geoyukon) by the [Government of Yukon](https://yukon.ca/maps) . Discover more digital map data and interactive maps from Yukon's digital map data collection.For more information: [geomatics.help@yukon.ca](mailto:geomatics.help@yukon.ca)

1:250,000 NTDB Cultural Area Features.Distributed from [GeoYukon](https://yukon.ca/geoyukon) by the [Government of Yukon](https://yukon.ca/maps) . Discover more digital map data and interactive maps from Yukon's digital map data collection.For more information: [geomatics.help@yukon.ca](mailto:geomatics.help@yukon.ca)

Regional stream sediment geochemical data compilationNovember 2020Release notesThe regional stream sediment geochemical data compilation comprises data for more than 30 000 samples across Yukon. This compilation updates the work of Héon (2003). This new compilation includes results from the reanalysis of more than 24 000 samples; inductively coupled plasma mass spectrometry (ICPMS) analysis provides upgraded detection limits and a broader range of elements relative to previous analytical data. In addition to analytical data, efforts have been made to improve sample location accuracy. The data in this release are organized by analytical method with the geodatabase having six feature classes:1. RGS_SITE_WATER - site specific physiography and water quality data. These data are unchanged from the original releases. 2. RGS_HEON - the same data as released in Héon (2003) with minor updates to sample location. 3. RGS_AAS - all samples analyzed by atomic absorption spectrometry. Most of these data are superseded by INAA and ICPMS data. 4. RGS_INAA - all samples analyzed by instrumental neutron activation analysis (INAA) and fire assay-neutron activation (FA-NA) analysis. 5. RGS_ICPMS - all samples analyzed by inductively coupled plasma mass spectrometry (ICPMS). 6. RGS_All - includes all AAS, INAA and ICPMS data. Collection of stream sediment samples in Yukon began in 1976 and ended in 2006. Three analytical methods have been used to analyze the minus 0.177 mm fraction (-80 mesh) of these samples: AAS, INNA (and FA-NA) and ICPMS. A simple description of each method is given below.For atomic absorption spectrometry (AAS) a 1 g aliquot is 'partially digested' using Lefort aqua regia or concentrated hot nitric acid. The digestion product is analyzed using an atomic absorption spectrometer. Oxide and silicate minerals are partially digested while some sulphide minerals are erratically volatilized. This means that AAS cannot be used to obtain accurate REE, Ta, Nb, As, Sb, Sn, Hg, Cr, or Au determinations.For instrumental neutron activation analysis ( INAA), aliquots of sieved sediment (the minus 0.177 mm fraction) or milled rock ranging from 5 to 40 g are encapsulated and irradiated in a nuclear reactor before counting the primary gamma radiation induced by the neutron irradiation with a high resolution germanium gamma ray detector. Fire assay-neutron activation (FA-NA) analysis is similar but includes a pre-concentration fire assay step prior to irradiation and analysis. Results for both INAA and FA-NA are similar to those for samples analyses by fusion or other total digestion techniques. Neutron activation detection limits are typically higher than those by acid digestion - ICPMS. Commodity and pathfinder elements such as Au, As, Sb and W have reasonable detection limits by INAA and the data generated are relatively precise.For ICPMS analysis, aliquots of sieved sediment ( the minus 0.177 mm fraction) ranging from 0.5 to 1 g are prepared using a partial digestion technique, typically aqua regia, followed by analysis of dissolution product by ICPMS. Sulphide minerals are completely oxidized and dissolved whereas most oxide and silicate minerals are only partially digested. This means that results produced by partial digestion methods are acceptable for elements such as Ag, As, Mo, Ni, Pb, Sb, Tl, and Zn but values for elements such as Al, Ba, Cr, Fe, P, Sn, Ti, Y, and Zr are likely to not reflect the actual element concentration in a sample. The sample size used for routine RGS sample analysis is too small be representative of Au in the original sample and thus Au by aqua regia digestion - ICPMS has poor precision.Further upgrades to this database are not anticipated. All samples that could be found in the GSC-Ottawa warehouse have been reanalyzed using ICPMS. Any errors or omissions in this database should be reported to the Yukon Geological Survey. Your feedback contributes to improving the accuracy of the geoscience databases for Yukon.Contact: [YGSMinerals@yukon.ca](mailto:YGSMinerals@yukon.ca) ; [geology@yukon.ca](mailto:geology@yukon.ca)Distributed from [GeoYukon](https://yukon.ca/geoyukon) by the [Government of Yukon](https://yukon.ca/maps) . Discover more digital map data and interactive maps from Yukon's digital map data collection.For more information: [geomatics.help@yukon.ca](mailto:geomatics.help@yukon.ca)