A literature review, focusing on oil sand products (e.g., diluted bitumen), diluents, spill-treating agents, and crude oil toxicology and ecological studies, relevant to the northeast Pacific was compiled as part of the Government of Canada’s World Class Tanker Safety program. Of the 763 references identified, 14 involved diluted bitumen and other heavy crude oils, indicating the need for further research of these products in the marine environment. Diluent research suggests relatively fast evaporation and dispersion times for this component, however high toxicities may pose a threat to marine biota. Historical studies indicate older dispersant formulations had potential ecological implications, therefore newer formulations, which have not been studied in detail, require full assessment. Consistent utilization of toxicology standards remains elusive, hindering species sensitivity analyses. Exxon Valdez literature demonstrates highly variable impacts from a single oil type and the need for baseline data, recovery status, and suitable ecological end-point determination.

A measure of the intrinsic susceptibility of an aquifer representing the tendency or likelihood for contaminants to reach a specified position in the groundwater system after introduction at some location above the uppermost aquifer. The method used to create the dataset is described in the metadata associated with the dataset. The dataset is a general assessment of the vulnerability of the hydrogeological unit considered as a whole. It features the local and regional qualifiers in a controlled vocabulary list referring to the extent where the vulnerability value is valid. Because the vulnerability is assessed using contextual indices linked to the regional hydrogeological settings, it is very unlikely to have an homogeneous range of data throughout the various hydrogeologic units across the country for this dataset. Hence, the vulnerability dataset will not qualify as an homogeneous dataset. A more generic reclassification using for examples three vulnerability classes could then be used to solve this problem. Each sub layers used to create the global vulnerability index can be provided along with the final vulnerability index map.

Hydro Features is composed of the network of Canadian surface waters. Hydro Features entities are: Watercourse, Water Linear Flow, Hydro Obstacle (falls, rapids\...), Waterbody (lake, watercourse\...), Permanent Snow and Ice, Water Well, and Spring. CanVec is a digital cartographic reference product of Natural Resources Canada (NRCan). It originates from the best available data sources covering Canadian territory, offers quality topographical information in vector format, and complies with international geomatics standards. CanVec is a multi-source product coming mainly from the National Topographic Data Base (NTDB), the Mapping the North process conducted by the Canada Center for Mapping and Earth Observation (CCMEO), the Atlas of Canada data, the GeoBase initiative, and the data update using satellite imagery coverage (e.g. Landsat 7, Spot, Radarsat, etc.).Distributed from [GeoYukon](https://yukon.ca/geoyukon) by the [Government of Yukon](https://yukon.ca/maps) . Discover more digital map data and interactive maps from Yukon's digital map data collection.For more information: [geomatics.help@yukon.ca](mailto:geomatics.help@yukon.ca)

The confinement describes the types of aquifer: confined, unconfined and semi-confined. Confined aquifer is bounded from above and below by impervious formations. Unconfined aquifer has a water table which serves as its upper boundary. Semi-confined aquifer is in between. Aquifer confinement is derived from geology, stratigraphy and hydrogeological unit thickness. The dataset represents the confinement assessment of the local area over the hydrogeological unit, from a controlled vocabulary.

The High Arctic dataset comes from the Petroleum and Environmental Management Tool (PEMT). The online tool was decommissioned in 2019 and the data was transferred to Open Data in order to preserve it.The PEMT was originally developed in 2009 to help guide development in the Canadian Arctic by Indian and Northern Affairs Canada (INAC). The online tool mapped the sensitivities of a variety of Arctic features, ranging from whales to traditional harvesting, across the Arctic. The tool was intended to aid government, oil and gas companies, Aboriginal groups, resource managers and public stakeholders in better understanding the geographic distribution of areas which are sensitive for environmental and socio-economic reasons. The study area is located in the High Arctic Archipelago and contains both marine and terrestrial components. The boundaries of the study area are based on the NOGB leasing grids applied in the High Arctic, under which exploration, significant discovery and production licenses may be issued. The Sverdrup Basin (and Lancaster Sound) has the highest known oil and gas potential of the sedimentary basins of the Arctic Islands (Nunavut Planning Commission 2000) and it is expected that there is oil and gas potential on Melville Island and Bathurst Island (Sivummut Economic Development Strategy Group 2003). To date, no gas has been produced, and 321,470 m³ of oil has been produced from the Bent Horn oil field (Morrell et al. 1995). DISCLAIMER: Please refer to the PEMT Disclaimer document or the Resource Constraints - Use Limitation in the Additional Information section below.Note: This is one of the 3 (three) datasets included in the PEMT application which includes the Beaufort Sea and Mackenzie Delta and Eastern Arctic datasets.

Hydro Features is composed of the network of Canadian surface waters. Hydro Features entities are: Watercourse, Water Linear Flow, Hydro Obstacle (falls, rapids\...), Waterbody (lake, watercourse\...), Permanent Snow and Ice, Water Well, and Spring. CanVec is a digital cartographic reference product of Natural Resources Canada (NRCan). It originates from the best available data sources covering Canadian territory, offers quality topographical information in vector format, and complies with international geomatics standards. CanVec is a multi-source product coming mainly from the National Topographic Data Base (NTDB), the Mapping the North process conducted by the Canada Center for Mapping and Earth Observation (CCMEO), the Atlas of Canada data, the GeoBase initiative, and the data update using satellite imagery coverage (e.g. Landsat 7, Spot, Radarsat, etc.).Distributed from [GeoYukon](https://yukon.ca/geoyukon) by the [Government of Yukon](https://yukon.ca/maps) . Discover more digital map data and interactive maps from Yukon's digital map data collection.For more information: [geomatics.help@gov.yk. ca](mailto:geomatics.help@yukon.ca)

Hydro Features is composed of the network of Canadian surface waters. Hydro Features entities are: Watercourse, Water Linear Flow, Hydro Obstacle (falls, rapids\...), Waterbody (lake, watercourse\...), Permanent Snow and Ice, Water Well, and Spring. CanVec is a digital cartographic reference product of Natural Resources Canada (NRCan). It originates from the best available data sources covering Canadian territory, offers quality topographical information in vector format, and complies with international geomatics standards. CanVec is a multi-source product coming mainly from the National Topographic Data Base (NTDB), the Mapping the North process conducted by the Canada Center for Mapping and Earth Observation (CCMEO), the Atlas of Canada data, the GeoBase initiative, and the data update using satellite imagery coverage (e.g. Landsat 7, Spot, Radarsat, etc.).Distributed from [GeoYukon](https://yukon.ca/geoyukon) by the [Government of Yukon](https://yukon.ca/maps) . Discover more digital map data and interactive maps from Yukon's digital map data collection.For more information: [geomatics.help@yukon.ca](mailto:geomatics.help@yukon.ca)

This layer is the current fire year burn severity classification for large fires (greater than 100 ha). Burn severity mapping is conducted using best available pre- and post-fire satellite multispectral imagery acquired by the MultiSpectral Instrument (MSI) aboard the Sentinel-2 satellite or the Operational Land Imager (OLI) sensor aboard the Landsat-8 and 9 satellites. Every attempt is made to use cloud, smoke, shadow and snow-free imagery that was acquired prior to September 30th. However, in late fire seasons imagery acquired after September 30th may be used. This layer is considered an interim product for the 1-year-later burn severity dataset (WHSE_FOREST_VEGETATION.VEG_BURN_SEVERITY_SP). Mapping conducted during the following growing season benefits from greater post-fire image availability and is expected to be more representative of tree mortality. #### Methodology: • Select suitable pre- and post-fire imagery or create a cloud/snow/smoke-free composite from multiple images scenes • Calculate normalized burn severity ratio (NBR) for pre- and post-fire images • Calculate difference NBR (dNBR) where dNBR = pre NBR – post NBR • Apply a scaling equation (dNBR_scaled = dNBR*1000 + 275)/5) • Apply BARC thresholds (76, 110, 187) to create a 4-class image (unburned, low severity, medium severity, and high severity) • Mask out water bodies using a satellite-derived water layer • Apply region-based filters to reduce noise • Confirm burn severity analysis results through visual quality control • Produce a vector dataset and apply Euclidian distance smoothing

This dataset provides the results obtained by Health Canada’s Canadian Radiological Monitoring Network (CRMN) for the gross alpha and beta activity concentrations in drinking water, given in units of becquerels per liter (Bq/L). More information about the CRMN network can be found on the Health Canada website (see link below). Although water quality is a matter of provincial jurisdiction, the CRMN, in collaboration with the city of Ottawa, has been conducting a targeted program to monitor the radiological content of drinking water from two water treatment plants in Ottawa, ON. The Guidelines for Canadian Drinking Water Quality recommend screening levels of 0.5 Bq/L and 1.0 Bq/L for gross alpha and gross beta activity, respectively. The screening levels are set to reflect the most restrictive Maximum Acceptable Concentrations (MACs) for specific radionuclides in drinking water. If the screening levels are not exceeded, compliance with the guidelines can be inferred. The screening levels set out in the Guidelines for Canadian Drinking Water Quality are calculated based on annual averages of radionuclides in drinking water. Short-term exposure to levels above those recommended by these guidelines does not indicate a health risk. The measured gross alpha and gross beta activity concentrations presented here are well below the screening levels set by the Guidelines for Canadian Drinking Water Quality, with only one exception to date. This occurred February 28, 2011, and was attributable to the flushing of lead pipes at the water treatment plant. It resulted in a spike of naturally occurring lead radionuclides that was dealt with immediately by the City of Ottawa. The map shows the approximate sampling location for each monitoring station. Stations are found within the associated location range.

The resource management features of the CanVec series include power lines, communication lines, pipelines, valves, petroleum wells, wind-operated devices, transformer stations, ore extraction sites, aggregate extraction sites, peat extraction sites and oil and gas sites.The CanVec multiscale series is available as prepackaged downloadable files and by user-defined extent via a Geospatial data extraction tool.Related Products (Open Maps Links):[Topographic Data of Canada - CanVec Series](https://open.canada.ca/data/en/dataset/8ba2aa2a-7bb9-4448-b4d7-f164409fe056)