Hydraulic properties characterize a hydrogeological unit. The hydraulic properties considered for this dataset are the transmissivity, the hydraulic conductivity, the storage coefficient, the specific storage coefficient and the porosity. Hydraulic properties are estimated by performing aquifer tests (pumping tests, slug tests). The hydraulic tests and their duration are managed in this dataset. The methods used to create the dataset are described in the metadata associated with the dataset. The dataset exhibits a general description of hydraulic properties of the hydrogeological unit, including hydraulic test, total test duration, method and date. It includes numbers and/or ranges describing the aquifer tests results. Note that an alternate raster representation could be used in complement to the discrete point-based representation.

A hydrogeological unit is defined as any soil or rock unit or zone that by virtue of its hydraulic properties has a distinct influence on the storage or movement of groundwater. It is considered the main dataset from the GGP point of view. Hydrogeological units are ranked into five levels (from largest to smallest): 1) hydrogeological region, 2) hydrogeological context, 3) aquifer system, 4) hydrostratigraphic unit, and 5) aquifer. Here are formal definitions for these different types of hydrogeologic units. - Hydrogeological region Hydrogeological regions are areas in which the properties of sub-surface water, or groundwater, are broadly similar in geology, climate and topography. There are 9 such regions identified in Canada (ref?). - Hydrogeological context Hydrogeological contexts are units of reporting, conceptually narrower than regions, and are additionally delineated by physiographic and hydrogeological aspects. - Aquifer system ""A heterogeneous body of intercalated permeable and poorly permeable material that functions regionally as a water-yielding hydraulic unit; it comprises two or more permeable beds [aquifers] separated at least locally by aquitards [confining units] that impede groundwater movement but do not greatly affect the regional hydraulic continuity of the system"" (Poland et al., 1972). - Hydrostratigraphic unit (HSU) ""Body of sediment and/or rock characterized by ground water flow that can be demonstrated to be distinct under both unstressed (natural) and stressed (pumping) conditions, and is distinguishable from flow in other HSUs"" (Noyes et al.) - Aquifer ""A formation, group of formations, or part of a formation that contains sufficient saturated permeable material to yield significant quantities of water to wells and springs"" (Lohman et al, 1972, p. 21). The rank attribute is used to specify the scope of the described unit. The general principle behind this specification is to allow the same data structure to apply to various types of hydrogeological units, from the local aquifer to the almost continental hydrogeological region. The dataset includes properties such as identification, physiography, geology, aquifer description and properties, water balance, groundwater use and risk. It features numerical values or a general description when no values are available. The description can also be used to add context to the numerical values. For each property, metadata identifying the source of the original data, links to similar data in GIN, and description of the processes, algorithms or methodology used to obtain these datasets will be available to complement the data. This dataset is designed to capture and represent a set of synthesized information pertaining to hydrogeological units through maps and succinct table reports. Some attributes (or properties) of the dataset are irrelevant depending of the rank of the unit. In general, this dataset is organised to include multiple properties associated with aquifers and larger hydrogeologic units. These properties are grouped into categories, which include identification, physiography, geology, aquifer description, water balance, groundwater use and risk. The numerical values associated with each of the properties can be used to create thematic maps; hence, the importance of using standardized units of measurement and definitions for these properties. When numerical values are not available, a general description may be supplied instead. The description can also be used to add context to the numerical values. Because this dataset is the cornerstone of the national view on groundwater, supplemental contextual information (metadata) must be part of the data. Thus, for each property, metadata identifying the source of the original data, links to similar data in GIN, and a description of the processes, algorithms or methodology used to obtain these datasets will be available to complement the data.

Water composition is defined by measuring the amounts of its various constituents; these are often expressed as milligrams of substance per litre of water (mg/L). Sampling methods vary according to the types of analysis. Dataset point: The dataset represents a general description of the sample, including name, ID, type of analysis and lab. It includes numbers describing the results of the analysis and physical properties of groundwater. Time series: The dataset represents a general description of the sample, including name, ID, type of analysis and lab. It includes series of numbers describing the results of the analysis and physical properties of groundwater with associated date. Dynamic values over time at the same sites provides temporal variation data of groundwater composition.

Groundwater flow is the movement of water in an aquifer or hydrogeological unit. The dataset shows groundwater flow rate and direction in the hydrogeological unit. Groundwater flow is establish from piezometric surface map. The method used to create the dataset is described in the metadata associated with the dataset. The dataset represents a description of the flow, including rate in m/d, direction, date and source. Typically, the data provided will not be in the form of a shapefile with linked properties but in the form of an image that sketches the groundwater flow. The image could also represent a cross section of the hydrogeologic units showing the regional trends of the groundwater flow.

In the hydrogeological unit, quantity of water that replenishes groundwater beneath the water table, expressed in mm/yr. Recharge is usually calculated using hydrology balance, integrating information from precipitation, hydrology data, drainage, soil properties, evapotranspiration, etc. The result is a raster dataset in which each cell has a given value for the recharge of the aquifer. It can be calculate using HELP software, developed by the US EPA. The methods used to create the dataset are described in the metadata associated with the dataset. The dataset represent a raster in which each cell has a mean value describing the global annual recharge of the hydrogeological unit.

The flood magnitude statistics can be used for applications such as flood plain delineation and design of hydraulic structures. The drought severity statistics can be used for applications such as water abstraction and effluent dilution.

This compilation sources data primarily from the Yukon Geological Survey’s (YGS) field projects and archival collections, and from the Geological Survey of Canada’s (GSC) Canadian rock physical property database (Enkin, 2014, 2018). The data distribution is far from uniform but covers a range of lithology classes and terranes. The compilation of data from archival samples is ongoing, and the dataset will continue to grow as new samples are collected for YGS projects and pass through the survey’s physical properties lab.The foundation of this dataset originates from samples collected for a mapping project in western Yukon led by Dirk Tempelman-Kluit from 1970 to 1972 (Tempelman-Kluit and Curie, 1978) and subsequently digitized by the Geological Survey of Canada and Mira Geoscience (2014). This dataset alone contributed 1642 records to the compilation. Map unit names from this original dataset were modernized for this compilation to reflect current understanding of Yukon geology.Systematic measurements of magnetic susceptibility and specific gravity have been incorporated into the workflow when archiving rock samples from YGS projects. Additional magnetic susceptibility measurements are also routinely collected in the field by YGS geologists. This will continue to expand the dataset. Rock samples are not collected specifically for the physical properties dataset but are well characterized and have sufficient metadata to be incorporated into the dataset. Samples are not uniform in size or weight.The Yukon Geological Survey’s HS Bostock Core Library houses >10 000 Yukon rock samples from previous and ongoing geological studies. Archived collections provide a great opportunity to further expand the dataset in specific regions or areas lacking representation.Distributed from [GeoYukon](https://yukon.ca/geoyukon) by the [Government of Yukon](https://yukon.ca/maps). Discover more digital map data and interactive maps from Yukon's digital map data collection.For more information: [geomatics.help@yukon.ca](mailto:geomatics.help@yukon.ca)

This dataset contains spatial and attribute data for local government Heritage Conservation Areas (HCAs) established for heritage conservation purposes in British Columbia, as tracked by BC Heritage Branch. Under the Local Government Act, a local government may designate a HCA within its Official Community Plan (OCP). An OCP may include a schedule of properties located within a Heritage Conservation Area that are considered to be protected heritage property. This is a multi-part polygon layer.

Surficial geologic units are unconsolidated materials overlying bedrock. The dataset represents a general description of the stratigraphy and geology, including geologic unit thickness, morphology, age and rank. It features a list of the geologic unit names and types of sediment in the hydrogeological unit. While the preferred format to deliver this data is by using a shapefile and its linked attributes, this dataset can be delivered also by providing link to external data which should have at least the same properties or also by joining a georeferenced image of the map.

This publication contains thirteen (13) maps of different biogeochemical and soil properties of forest ecosystems of Canada’s managed forest. A scientific article gives additional details on the methodology: Paré, D., Manka, F., Barrette, J., Augustin, F., Beguin, J. 2021. Indicators of site sensitivity to the removal of forest harvest residues at the sub-continental scale: mapping, comparisons, and challenges. Ecol. Indicators. https://dx.doi.org/10.1016/j.ecolind.2021.107516