Groundwater flow is the movement of water in an aquifer or hydrogeological unit. The dataset shows groundwater flow rate and direction in the hydrogeological unit. Groundwater flow is establish from piezometric surface map. The method used to create the dataset is described in the metadata associated with the dataset. The dataset represents a description of the flow, including rate in m/d, direction, date and source. Typically, the data provided will not be in the form of a shapefile with linked properties but in the form of an image that sketches the groundwater flow. The image could also represent a cross section of the hydrogeologic units showing the regional trends of the groundwater flow.

The Wastewater Systems Effluent Regulations (WSER), developed under the Fisheries Act, came into force in 2012 to manage wastewater releases by systems that collect an average daily influent volume of 100 cubic metres or more. The WSER also does not apply to any wastewater system located in the Northwest Territories, Nunavut and north of the 54th parallel in the provinces of Quebec and Newfoundland and Labrador. The WSER set national baseline effluent quality standards that are achievable through secondary wastewater treatment. The map below presents data regarding compliance with the WSER effluent quality standards according to their averaging period. Wastewater systems must report on either a monthly, quarterly or annual basis. The dataset also includes the carbonaceous biochemical oxygen demand (CBOD) and suspended solids (SS) results for each wastewater system. Annual reporting: This map layer shows whether or not the wastewater systems met the WSER effluent quality limit according to an annual averaging period for carbonaceous biochemical oxygen demand CBOD or suspended solids SS. Quarterly reporting: This map layer shows whether or not the wastewater systems met the WSER effluent quality standards according to a quarterly averaging period. Note that a system that meets its CBOD limit or its SS limit for more than 75% of the time is considered to be in compliance with the effluent quality standards of the WSER.Monthly reporting: This map layer shows whether or not the wastewater systems met the WSER effluent quality standards according to a monthly averaging period. Note that a system that meets its CBOD limit or its SS limit for more than 75% of the time is considered to be in compliance with the effluent quality standards of the WSER.The map is available in both ESRI REST (to use with ARC GIS) and WMS (open source) formats. For more information about the individual reporting wastewater systems, datasets are available in either CSV or XLS formats.Data from Quebec and YukonThe data for Quebec municipalities (after 2017) is provided to the department separately through the equivalency agreement that was finalized in October 2018. Beginning in 2015, the data reported for the Yukon is provided to the department separately through an equivalency agreement finalized in 2014.More information on the wastewater sector including the regulations, agreements, contacts and resource documents is available at: https://www.canada.ca/wastewater 

The Wastewater Systems Effluent Regulations (WSER), developed under the Fisheries Act, came into force in 2012 to manage wastewater releases by systems that collect an average daily influent volume of 100 cubic metres or more. The WSER also does not apply to any wastewater system located in the Northwest Territories, Nunavut and north of the 54th parallel in the provinces of Quebec and Newfoundland and Labrador. The WSER set national baseline effluent quality standards that are achievable through secondary wastewater treatment. The WSER require owners or operators of wastewater systems with combined sewers to submit an annual report on the total volume and the number of days wastewater is discharged per month via combined sewer overflow (CSO) points as a result of precipitation.The map below shows the volume of effluent (in cubic metres) discharged in a year from all CSO points situated within the collection area of a wastewater system. For the most part, the volumes provided to ECCC are estimates.Please note, a value of “999999999” in the dataset indicates that the volume data is unavailable and it does not mean that a volume of 999,999,999 m3 was released within the collection area of a wastewater system.The map is available in both ESRI REST (to use with ARC GIS) and WMS (open source) formats. For more information about the individual reporting wastewater systems, datasets are available in either CSV or XLS formats.Data from QuebecAs of 2018, no combined sewer overflow volumes from Quebec municipalities are available since an equivalency agreement is now in effect.More information on the wastewater sector including the regulations, agreements, contacts and resource documents is available at: https://www.canada.ca/wastewater

The Wastewater Systems Effluent Regulations (WSER), developed under the Fisheries Act, came into force in 2012 to manage wastewater releases by systems that collect an average daily influent volume of 100 cubic metres or more. The WSER also does not apply to any wastewater system located in the Northwest Territories, Nunavut and north of the 54th parallel in the provinces of Quebec and Newfoundland and Labrador. The WSER set national baseline effluent quality standards that are achievable through secondary wastewater treatment. The map below presents the wastewater system locations in Canada and the type of treatment they utilize (mechanical, lagoon or no treatment). The data is based on the information submitted to Environment and Climate Change Canada as of November 2022. Note that this layer does not represent the level of wastewater treatment or whether the system complies with the WSER.The map is available in both ESRI REST (to use with ARC GIS) and WMS (open source) formats. For more information about the individual reporting wastewater systems, datasets are available in either Excel or CSV formats at the resource listed below: “Wastewater Systems Effluent Regulations Reported Data”.Data from Quebec and YukonThe data for Quebec municipalities (after 2017) is provided to the department separately through the equivalency agreement that was finalized in October 2018. Beginning in 2015, the data reported for the Yukon is provided to the department separately through an equivalency agreement finalized in 2014.More information on the wastewater sector including the regulations, agreements, contacts and resource documents is available at: https://www.canada.ca/wastewater

Digitization of long-term water chemistry data collected between 1920's - 1990's from lakes across Saskatchewan by the Saskatchewan Fisheries Research Laboratory. Samples were collected using methods from the Standard Methods for the Examination of Water and Wastewater (APHA, AWWA and WPCF). This data serves as a baseline for water quality.This dataset is a digitization from paper records of water chemistry data across Saskatchewan collected by the Saskatchewan Fisheries Research Laboratory. Data ranges from the 1920's to the 1990's and were sampled using methodes from the Standard Methods for the Examination of Water and Wastewater (American Public Health Association, American Water Works Association and Water Pollution Control Facility) This long-term water chemistry data serves as a baseline for water quality. Different variables of water chemistry are organized into individual fields. The units of measurement appear at the end of each field name. Due to the historical nature of the data some uncertainty exist in values.  Additonal notes on data: ND: no detection Trace: trace amounts Nil: zero NA: no data 

This dataset is a compilation of numerous data files recovered as part of a data request in 2024 from a historical archive of DFO research data. Sediment and Suspended Particulate Matter (SPM) samples were collected over more than a decade as part of Dr. Douglas Loring’s research program while working at the Bedford Institute of Oceanography (BIO). Samples were collected as part of individual and collaborative research projects, and links to the relevant primary science publications and reports are included in the data in an effort to provide context to the data, as well as describe the field and laboratory techniques used to generate the attached data.

Water composition is defined by measuring the amounts of its various constituents; these are often expressed as milligrams of substance per litre of water (mg/L). Sampling methods vary according to the types of analysis. Dataset point: The dataset represents a general description of the sample, including name, ID, type of analysis and lab. It includes numbers describing the results of the analysis and physical properties of groundwater. Time series: The dataset represents a general description of the sample, including name, ID, type of analysis and lab. It includes series of numbers describing the results of the analysis and physical properties of groundwater with associated date. Dynamic values over time at the same sites provides temporal variation data of groundwater composition.

The contaminants in fish database is a compilation of contaminant data analysed from fish tissue at the Fresh Water Institute from 1970 to 2005. Data include lab number, region, analysis, organs, species, lake, form (whole fish, headon dressed, headless dressed), weight, and length and contaminant concentrations. Total mercury was the predominant contaminant measured. Results were expressed as ppm or ppb based on the parameter analyzed. Concentrations are expressed based on wet weight.

Normal Annual Runoff for 1961 - 1990, in mm

The Wastewater Systems Effluent Regulations (WSER), developed under the Fisheries Act, came into force in 2012 to manage wastewater releases by systems that collect an average daily influent volume of 100 cubic metres or more. The WSER also does not apply to any wastewater system located in the Northwest Territories, Nunavut and north of the 54th parallel in the provinces of Quebec and Newfoundland and Labrador. The WSER set national baseline effluent quality standards that are achievable through secondary wastewater treatment. Under the WSER, owners or operators of wastewater systems discharging annual average daily effluent volumes greater than 2,500 m3 are required to determine and report on the acute lethality of the effluent.The map below presents the percentage of acute lethality test failures for the wastewater systems in Canada that conducted at least one acute lethality test according to the standards of the Wastewater Systems Effluent Regulations. The map is available in both ESRI REST (to use with ARC GIS) and WMS (open source) formats. For more information about the individual reporting wastewater systems, datasets are available in either Excel or CSV formats.Data from Quebec and YukonAs of 2018, no acute lethality results from Quebec municipalities are available since an equivalency agreement is now in effect. As of 2015, no acute lethality test results for wastewater systems in the Yukon are available as an equivalency agreement in is effect.More information on the wastewater sector including the regulations, agreements, contacts and resource documents is available at: https://www.canada.ca/wastewater