Highway Maintenance Class defines the level of service for maintenance of the highway, normally, a function of the traffic usage type and traffic volume. This layer contains polylines

The land classification shown is derived from in-field investigation and is only undertaken for project investigation purposes. These polygons represent the most accurate and up-to-date information regarding agriculture land conditions at those specific locations.Distributed from [[GeoYukon](.underline)](https://yukon.ca/geoyukon) by the [[Government of Yukon](.underline)](https://yukon.ca/maps) .Discover more digital map data and interactive maps from Yukon's digital map data collection. For more information: [[geomatics.help@yukon.ca](.underline)](mailto:geomatics.help@yukon.ca)

The purpose of this feature class is to identify the individual annual allowable cut and annual limit areas as referred to in the Forest Resources Act subsection 20(2) and 31(10 of the Forest Resources Regulation). Where there is no approved Forest Resources Management Plan (FRMP) for an area, forest resources harvesting can only be authorized in an amount less than that prescribed by regulation for that area. The Forest Resources Regulation subsection 31(1) establishes the annual limits for harvesting timber resources for areas without an FRMP. These areas are referred to as the Annual Limit Regions in Schedule 1 of the Regulation titled Timber Harvesting Areas. These annual limits are set as the annual allowable cut for each of the areas, until such time as a Forest Resources Management Plan is approved for that area.Distributed from [GeoYukon](https://yukon.ca/geoyukon) by the [Government of Yukon](https://yukon.ca/maps) . Discover more digital map data and interactive maps from Yukon's digital map data collection.For more information: [geomatics.help@yukon.ca](mailto:geomatics.help@yukon.ca)

The purpose of this feature class is to identify the forest resources management zones within a Forest Resources Management Plan, as per subsection 2(h) of the Forest Resources Regulation. These sub-divided smaller forest planning areas or landscape units are based on watershed boundaries and modified by local access and development patterns. They usually contain similar management concerns and forest types. The units form the boundaries for detailed information gathering, monitoring and planning.Distributed from [GeoYukon](https://yukon.ca/geoyukon) by the [Government of Yukon](https://yukon.ca/maps) . Discover more digital map data and interactive maps from Yukon's digital map data collection.For more information: [geomatics.help@yukon.ca](mailto:geomatics.help@yukon.ca)

Double line streams from FC1 assigned a stream class

The purpose of this feature class is to identify those areas that are in the process of Timber Harvest Planning, process being a continuum from proposed plan through to approval and eventually plan expiration. Subsection 20(3) of the Forest Resources Act establishes that an approved Timber Harvest Plan is required prior to the authorization of timber harvesting under a Harvesting Licence or authorization of a Forest Resources Permit for non-commercial timber harvesting in an amount greater than 25m3 per year. A Timber Harvest Plan:• Must be developed in accordance with Sections 5 through 7 of the Forest Resources Regulation. • Identifies forest resources in the area and areas suitable for timber harvesting and establishes objectives for timber harvesting.• Must be consistent with any Forest Resources Management Plan that applies to the same area.Distributed from [GeoYukon](https://yukon.ca/geoyukon) by the [Government of Yukon](https://yukon.ca/maps) . Discover more digital map data and interactive maps from Yukon's digital map data collection.For more information: [geomatics.help@yukon.ca](mailto:geomatics.help@yukon.ca)

Predicted Soil Great Group class as defined by the The Canadian System of Soil Classification (third edition).

A building is a structure that has a roof and walls and stands more or less permanently in one place. Symbols are used when buildings and structures are permanent landmarks. Symbolized buildings have no side larger than 50 metres for 1:20,000 data or no side larger than 30 metres for 1:10,000 data. Small structures (including buildings less than 50 square metres) are not shown unless they constitute a point of orientation. This product requires the use of geographic information system (GIS) software. [Land Information Ontario: Data Class Fact Sheet - Building to Scale (PDF)](https://www.sdc.gov.on.ca/sites/MNRF-PublicDocs/EN/CMID/Building%20to%20Scale%20-%20Data%20Description.pdf)

__The link: *Access the data directory* is available in the section*Dataset Description Sheets; Additional Information*__.**Slope classes** express the slope of the terrain in a relatively homogeneous area with a minimum area of 0.5 ha. They are generated from a numerical model that groups terrain slopes into six classes:+ 0-3% zero + Low by 4-8% + 9-15% soft + Moderate by 16-30% + 31-40% strong + Steep by 41% or moreThese data cover almost all of Quebec south of the 52nd parallel. This map is presented in two groups: grouping at the provincial level and grouping at the scale of 1/250,000. Each grouping represents an assembly of sheets produced on a scale of 1/20,000.The datasets were originally produced in 2005 and then updated in 2006. In 2010, they were enhanced with slope information for the northernmost part. No updates have been made since then.__For more information, please refer to the document: [Products presenting the concept of slope] (https://diffusion.mffp.gouv.qc.ca/Diffusion/DonneeGratuite/Foret/DONNEES_FOR_ECO_SUD/Classes_pente/01-Documentation/Produits_presentant_la_notion_de_pente.pdf)____ ⚠️ Notes: __ The numerical terrain model is prepared from the level curves and altitude points that come from the topographic map at a scale of 1/20,000 and 1/50,000 from the Quebec Topographic Database (BDTQ). This geographic database was produced in 2010 and has never been updated.__ 🕰️ Former names:__ Numerical slope classes, Slope class**This third party metadata element was translated using an automated translation tool (Amazon Translate).**

The Plains, Northern, Foothills Boundary feature class contains polygon features representing Department of Energy Regional Boundaries for the Province of Alberta.