Wildfire change magnitude 1985-2022. Spectral change magnitude for wildfires that occurred from 1985 to 2022. It is developed within the framework of Canada’s National Terrestrial Ecosystem Monitoring System (NTEMS). The wildfire change magnitude included in this product is expressed via differenced Normalized Burn Ratio (dNBR), computed as the variation between the spectral values before and after a given change event. Higher dNBR values are related to higher burn severity. Time series of Landsat data with 30-m spatial resolution were used to characterize national trends in stand replacing forest disturbances caused by wildfire for the period 1985-2022 for Canada's 650 million-hectare forested ecosystems.When using this data, please cite as: Hermosilla, T., M.A. Wulder, J.C. White, N.C. Coops, G.W. Hobart, L.B. Campbell, 2016. Mass data processing of time series Landsat imagery: pixels to data products for forest monitoring. International Journal of Digital Earth 9(11), 1035-1054. (Hermosilla et al. 2016).See references below for an overview on the data processing, metric calculation, change attribution and time series change detection methods applied, as well as information on independent accuracy assessment of the data.Hermosilla, T., Wulder, M. A., White, J. C., Coops, N.C., Hobart, G.W., 2015. An integrated Landsat time series protocol for change detection and generation of annual gap-free surface reflectance composites. Remote Sensing of Environment 158, 220-234. (Hermosilla et al. 2015a).Hermosilla, T., Wulder, M.A., White, J.C., Coops, N.C., Hobart, G.W., 2015. Regional detection, characterization, and attribution of annual forest change from 1984 to 2012 using Landsat-derived time-series metrics. Remote Sensing of Environment 170, 121-132. (Hermosilla et al. 2015b).

Harvest changes occurred from 1985 to 2022 displaying the year of greatest harvest disturbance. It is developed within the framework of Canada’s National Terrestrial Ecosystem Monitoring System (NTEMS). The information outcomes represent 38 years of harvest activity in Canada's forests, derived from a single, consistent, spatially explicit data source in a fully automated manner. Time series of Landsat data with 30 m spatial resolution were used to characterize national trends in stand replacing forest disturbances caused by harvest for the period 1985-2022 for Canada's 650-million-hectare forested ecosystems.When using this data, please cite as: Hermosilla, T., M.A. Wulder, J.C. White, N.C. Coops, G.W. Hobart, L.B. Campbell, 2016. Mass data processing of time series Landsat imagery: pixels to data products for forest monitoring. International Journal of Digital Earth 9(11), 1035-1054. https://doi.org/10.1080/17538947.2016.1187673 ( Hermosilla et al. 2016).See references below for an overview on the data processing, metric calculation, change attribution, and time series change detection methods applied, as well as information on independent accuracy assessment of the data.Hermosilla, T., Wulder, M. A., White, J. C., Coops, N.C., Hobart, G.W., (2015). An integrated Landsat time series protocol for change detection and generation of annual gap-free surface reflectance composites. Remote Sensing of Environment 158, 220-234. ( Hermosilla et al. 2015a).Hermosilla, T., Wulder, M.A., White, J.C., Coops, N.C., Hobart, G.W., (2015). Regional detection, characterization, and attribution of annual forest change from 1984 to 2012 using Landsat-derived time-series metrics. Remote Sensing of Environment 170, 121-132. ( Hermosilla et al. 2015b).Hermosilla, T., M.A. Wulder, J.C. White, N.C. Coops, G. W. Hobart, (2017). Updating Landsat time series of surface-reflectance composites and forest change products with new observations. International Journal of Applied Earth Observation and Geoinformation. 63,104-111. https://doi.org/10.1016/j.jag.2017.07.013 (Hermosilla et al. 2017)

The High Resolution Digital Elevation Model Mosaic provides a unique and continuous representation of the high resolution elevation data available across the country. The High Resolution Digital Elevation Model (HRDEM) product used is derived from airborne LiDAR data (mainly in the south) and satellite images in the north. The mosaic is available for both the Digital Terrain Model (DTM) and the Digital Surface Model (DSM) from web mapping services. It is part of the CanElevation Series created to support the National Elevation Data Strategy implemented by NRCan. This strategy aims to increase Canada's coverage of high-resolution elevation data and increase the accessibility of the products.Unlike the HRDEM product in the same series, which is distributed by acquisition project without integration between projects, the mosaic is created to provide a single, continuous representation of strategy data. The most recent datasets for a given territory are used to generate the mosaic. This mosaic is disseminated through the Data Cube Platform, implemented by NRCan using geospatial big data management technologies. These technologies enable the rapid and efficient visualization of high-resolution geospatial data and allow for the rapid generation of dynamically derived products. The mosaic is available from Web Map Services (WMS), Web Coverage Services (WCS) and SpatioTemporal Asset Catalog (STAC) collections. Accessible data includes the Digital Terrain Model (DTM), the Digital Surface Model (DSM) and derived products such as shaded relief and slope.The mosaic is referenced to the Canadian Height Reference System 2013 (CGVD2013) which is the reference standard for orthometric heights across Canada.Source data for HRDEM datasets used to create the mosaic is acquired through multiple projects with different partners.Collaboration is a key factor to the success of the National Elevation Strategy. Refer to the “Supporting Document” section to access the list of the different partners including links to their respective data.

TA_CROWN_INCLUSIONS_SVW contains the spatial representation (polygon) of active and applied for Crown Land Inclusions. Inclusions are a mechanism by which an interest holder can extend for inclusion their holdings based on statutory provisions within the Land and Land Title Acts. The view was created to provide a simplified presentation of this single tenure type from the disposition information in the Tantalis operational system. The same content could be derived from the TA_CROWN_TENURES_SVW by filtering to this tenure type only

Wildfire change year 1985-2022.Wildfire changes occurred from 1985 to 2022 displaying the year of greatest wildfire disturbance. It is developed within the framework of Canada’s National Terrestrial Ecosystem Monitoring System (NTEMS). The information outcomes represent 38 years of wildfires in Canada's forests, derived from a single, consistent, spatially explicit data source in a fully automated manner. Time series of Landsat data with 30 m spatial resolution were used to characterize national trends in stand replacing forest disturbances caused by wildfire for the period 1985-2022 for Canada's 650-million-hectare forested ecosystems.When using this data, please cite as: Hermosilla, T., M.A. Wulder, J.C. White, N.C. Coops, G.W. Hobart, L.B. Campbell, 2016. Mass data processing of time series Landsat imagery: pixels to data products for forest monitoring. International Journal of Digital Earth 9(11), 1035-1054. https://doi.org/10.1080/17538947.2016.1187673 (Hermosilla et al. 2016).See references below for an overview on the data processing, metric calculation, change attribution, and time series change detection methods applied, as well as information on independent accuracy assessment of the data..Hermosilla, T., Wulder, M. A., White, J. C., Coops, N.C., Hobart, G.W., (2015). An integrated Landsat time series protocol for change detection and generation of annual gap-free surface reflectance composites. Remote Sensing of Environment 158, 220-234. https://doi.org/10.1016/j.rse.2014.11.005 (Hermosilla et al. 2015a).Hermosilla, T., Wulder, M.A., White, J.C., Coops, N.C., Hobart, G.W., (2015). Regional detection, characterization, and attribution of annual forest change from 1984 to 2012 using Landsat-derived time-series metrics. Remote Sensing of Environment 170, 121-132. https://doi.org/10.1016/j.rse.2015.09.004 (Hermosilla et al. 2015b).Hermosilla, T., M.A. Wulder, J.C. White, N.C. Coops, G. W. Hobart, (2017). Updating Landsat time series of surface-reflectance composites and forest change products with new observations. International Journal of Applied Earth Observation and Geoinformation. 63,104-111. https://doi.org/10.1016/j.jag.2017.07.013 (Hermosilla et al. 2017).

Facilities that separate and convert crude oil or other feedstock into liquid petroleum products, including upgraders and asphalt refineries.Mapping Resources implemented as part of the North American Cooperation on Energy Information (NACEI) between the Department of Energy of the United States of America, the Department of Natural Resources of Canada, and the Ministry of Energy of the United Mexican States.The participating Agencies and Institutions shall not be held liable for improper or incorrect use of the data described and/or contained herein. These data and related graphics, if available, are not legal documents and are not intended to be used as such. The information contained in these data is dynamic and may change over time and may differ from other official information. The Agencies and Institutions participants give no warranty, expressed or implied, as to the accuracy, reliability, or completeness of these data.

Bioterrain (TBT) contains polygons with key and amalgamated (concatenated) attributes derived from the RISC (Resource Inventory Standards Committee) standard attributes. TBT divides the landscape into units using the Terrain Classification System for British Columbia and ecological criteria. Polygon attributes include (but are not limited to) surficial material, surface expression, geomorphological processes, drainage class and aspect. TBT methods include manual air photo interpretation supported by selective field checking. Bioterrain mapping is integral to ecosystem mapping and its derivative products. This layer is derived from the STE_TEI_ATTRIBUTE_POLYS_SP layer by filtering on the PROJECT_TYPE attribute. Project types include: TEM, TEMNSS, TEMPRE, TEMSEI, TEMSET, TEMTSM, TBS, TBT, TEMWHR, TEMSDM, TEMPRW, and TEMSEW. Current version: v11 (published on 2024-10-03) Previous versions: v10 (published on 2023-11-14), v9 (published on 2023-03-01), v8 (published on 2016-09-01)

These products are derived from RGB (red/green/blue) images, a satellite processing technique that uses a combination of satellite sensor bands (also called channels) and applies a red/green/blue (RGB) filter to each of them. The result is a false-color image, i.e. an image that does not correspond to what the human eye would see, but offers high contrast between different cloud types and surface features. The on-board sensor of a weather satellite obtains two basic types of information: visible light data (reflected light) reflecting off clouds and different surface types, also known as "reflectance", and infrared data (emitted radiation) which are long-wave radiations emitted by clouds and surface features. RGBs are specially designed to combine this type of satellite data, resulting in an information-rich final product. Four types of products are currently generated from the GOES-West and GOES-East satellites: "NightIR" and "NightMicrophysics", at 2km resolution, are generated 24 hours a day with infrared channels, so are visible both night and day, and "NaturalColour" and "DayCloudConvection", at 1km resolution, which combine visible light channels with infrared channels; their higher resolution makes the latter two products more popular, but they are not available during most of the night (between 02UTC and 07UTC for GOES-Est, and between 06UTC and 11UTC for GOES-Ouest) given the absence of reflected sunlight. Other RGB products should be added gradually in the future to meet different needs.

River ice roughness products from the last three days in selected Canadian regions that have been designated for observation, monitored by Natural Resources Canada using satellite imagery for emergency response. Coverage is not comprehensive nationwide. In order to mitigate ice jam induced flood risks, Natural Resources Canada emergency geomatics service (EGS) may be activated by Canada’s emergency management authorities. As new satellite imagery becomes available, NRCan will produce river ice roughness maps and update the dataset in near real time (4 hours). This item contains the latest river ice roughness products generated in the past three days. For any data older than 72 hours, please refer to the [River Ice in Canada - Current Year](https://open.canada.ca/data/en/dataset/8ca6f047-ddef-43d7-81c2-47654f4c69bd) entry. The river ice product is generated and validated on a best effort basis. Various factors may affect the quality of the river ice roughness maps. Those factors include but are not limited to: environmental condition at the time of acquisition, image resolution or the limitations of the methodology used. To view a specific product in Web Services, filter the data by date (UTC Date) and area of interest (AOI). A link to download specific EGS products is available in the Resources section.Disclaimer:Emergency response authorities are the primary users of these satellite-derived river ice roughness map products. These products are generated to provide analysis and emergency response situational awareness and to facilitate decision-making during major flood events. The river ice roughness products are generated rapidly and limited time is available for editing and validation. The river ice roughness products reflect the river ice surface roughness conditions at the date/time of acquisition. While efforts are made to produce high quality products, near-real time products may contain errors due to the limited time available for validation and the limited availability of ground truthing data. Limitation of Liability:Accordingly, the information contained on this website is provided on an “as is” basis and Natural Resources Canada makes no representations or warranties respecting the information, either expressed or implied, arising by law or otherwise, including but not limited to, effectiveness, completeness, accuracy or fitness for a particular purpose. Natural Resources Canada does not assume any liability in respect of any damage or loss based on the use of this website. In no event shall Natural Resources Canada be liable in any way for any direct, indirect, special, incidental, consequential, or other damages based on any use of this website or any other website to which this site is linked, including, without limitation, any lost profits or revenue or business interruption.Parent Collection:- **[River Ice State in Canada - Cartographic Product Collection](https://open.canada.ca/data/en/dataset/d1fcb44f-5f86-4957-bdb4-e6fd1aa69283)**

The dataset includes two data products derived from the Visible Infrared Imaging Radiometer Suite (VIIRS) imager operated by the US National Oceanic and Atmospheric Administration (NOAA) onboard Suomi National Polar-Orbiting Partnership (SNPP) satellite:1) Normalized Difference Vegetation Index (NDVI)2) Snow Mask (Snow) with supplementary information about data quality and scene identificationEach product, NDVI and Snow, has been derived at two spatial resolutions: 1) I-band resolution for 250-m spatial grid (VIIRS image bands I1 and I2)2) M-band resolution for 500-m spatial grid (VIIRS moderate resolution bands M5 and M7)Datasets are produced with a daily temporal frequency, i.e. one file per day. The study area with the size of 5,700 km × 4,800 km covers Canada and neighboring regions (Trishchenko, 2019). The VIIRS time series are produced from VIIRS /SNPP imagery at CCRS from January 1, 2017.