TA_CROWN_LEASES_SVW - A Crown Land Lease is a type of land tenure issued under the Land Act. A Land Act Lease is issued where long term tenure is required, where substantial improvements are proposed, and/or where definite boundaries are required in order to avoid land use and property conflicts. The tenure holder is granted the exclusive use and enjoyment of the area. The tenure holder also has the right to exclude or charge the public for use of the land and/or improvements, when this is consistent with the terms of the lease. Crown Leases require a (cadastral) survey prior to issuance

This spatial layer displays Range Tenures (grazing and hay cutting licence and permits) administered by the Ministry of Forests, Lands and Natural Resource Operations. A Range Tenure is an area of Crown rangeland where a Range Act tenure applies. Tenure holders access a defined amount of forage through grazing (measured in Animal Unit Months) or hay (tonnage). Range Tenures apply only to Crown Land. In some cases, digital boundaries may overlap Private Land but these lands are not part of the Grazing area (as described in the legal description). Grazing may overlap waterbodies during drawdown (also described legally in the Tenure documents and where applicable, Range Use Plan). Livestock may graze islands and large bodies of water may act as Natural Range Barriers. March 3, 2023: Updates to the Range Tenure attribute table as described. Please contact Nancy.Elliot@gov.bc.ca if you have questions. To guide your use: 1. Layer contains RETIRED, PENDING, and ACTIVE Tenures (=Licenses and Permits); Select ACTIVE under attribute LIFE_CYCLE_STATUS_CODE to isolate all active tenures (status refers to spatial boundary status - therefore, a spatial boundary must be Retired in the Forest Tenure Administration system to have a status of retired); 2. Unique ID for Polygon is by RAN# in attribute FOREST_FILE_ID. Each tenure has own its RAN# (e.g. RAN07777). Multiple areas (polygons) belonging to the same tenure may have same RAN# with unique map block ids (e.g. RAN07777 A, RAN07777 B) 3. The field SUM_TENURE_ACTIVE_AREA_HA will provide, where LIFE_CYCLE_STATUS_CODE is ACTIVE, the total tenure area in Ha. For single block (polygon) tenures, this will be the same area as the polygon. Where there are multiple blocks, this will be the total sum area of all Active blocks. (Note this does not include PENDING or RETIRED tenure areas. Area is for Approved and Active Tenure boundaries. A block may be Approved but Pending, and therefore is not included). Review data for multipart vs multi polygons 4. AUTHORIZED_USE and TOTAL_ANNUAL_USE are for the entire Tenure; where there are multiple blocks, the total is over all blocks, seasonally distributed through different pastures 3. FILE_TYPE_CODE contains information on the type of Permit: • E01 - Grazing License • E02 - Grazing Permit • H01 - Haycutting License • H02 - Haycutting Permit 4. IF YOU ARE DOING SPATIAL ANALYSIS based on AREA --- Please note that tenures overlap either partially or wholly amongst tenure holders. One area may be shared by more than one Tenure holder and therefore there will be multiple congruent or partially overlapping polygons (multipart). If you want to do SPATIAL ANALYSIS based strictly on area, you must collapse or flatten the data using DISSOLVE so that the polygons are 1:1 with the land base (suggested approach)

Long-term tenure map (managed forest code 11) used in the Forest Management in Canada, 2020 story map.Long-term tenure map (managed forest code 11) with lands having more than five years volume- or area-based tenure or effectively having the equivalent, such as consistently recurrent commercial forest tenure with associated forest management activity. The Long-term tenure map is used in the Story Map of Forest Management in Canada, 2020 (Aménagement des forêts au Canada, 2020) and includes the following tiled layer:Tile Layer of Long-Term Tenure Managed Forest Code 11: 2020

TA_CROWN_RSRV_NOTATIONS_SVW contains the spatial representation (polygon) of active and applied for Reserves and Notations. Reserves are a particular type of crown land tenure that grants an agency the right to implement a restriction on the use of crown land. Federal and Provincial government agencies and corporations may apply for the establishment of Land Act Reserves over high value sites required for public purposes, including research and education. Depending on the type of reserve (Order in Council, Map Reserve, Land Act Designation (which can be designated use or prohibitive use) and Notation of Interest) the area is withdrawn from disposition under the Land Act. The view was created to provide a simplified presentation of this single tenure type from the disposition information in the Tantalis operational system. The same content could be derived from the TA_CROWN_TENURES_SVW by filtering to this tenure type only

Tenure Areas are geographic administrative areas named for local features and used to group petroleum and natural gas Land Plats situated within the same local geographic area.

Short-term tenure map (managed forest code 12) used in the Story Map of Forest Management in Canada, 2017.Short-term tenure map (managed forest code 12) used in the  Story Map of Forest Management in Canada, 2017. Short-Term Tenure areas are lands having shorter-term volume- or area-based tenure. Tenure arrangements can be overlapping. Lands with both long- and short-term tenures are classified as Long-Term Tenure (Code 11). Source:  This web map shows the short-term tenure areas used in the map of forest management in Canada, 2017 and includes the following tiled layer: Short-Term Tenure (Managed Forest Code 12)Data provided by Alberta Agriculture and Forestry; British Columbia Ministry of Forests; Manitoba Sustainable Development; Natural Resources Canada; New Brunswick Department of Energy and Resource Development; Newfoundland & Labrador Department of Fisheries and Land Resources; Northwest Territories Department of Environment and Natural Resources; Nova Scotia Department of Lands and Forestry; Ontario Ministry of Natural Resources and Forestry; Prince Edward Island Department of Communities, Land & Environment; Québec Ministère des Forêts, de la Faune et des Parcs; Saskatchewan Ministry of Environment; and Yukon Energy, Mines and Resources.

TA_CROWN_RIGHTS_OF_WAY_SVW contains the spatial representation (polygon) of active and applied for Statutory Rights-of-way. Statutory rights-of-way are registerable in a Land Titles office, and are normally issued to authorize linear uses of Crown Land for transportation, communication, energy production and utility developments. They grant tenure holders right of passage for specific purposes and certainty respecting access to the land and use of improvements. They do not convey non-exclusive use - exclusivity may be granted for safety reasons. A legal survey is required to define the tenured area. The view was created to provide a simplified presentation of this single tenure type from the disposition information in the Tantalis operational system. The same content could be derived from the TA_CROWN_TENURES_SVW by filtering to this tenure type only

Uniquely identifies a 75 metre wide road tenure. This layer uses the centre line from the application and is buffered 37.5 metres either side. This layer does not represent the actual road on the ground. It represents where the application area is

Health Service Delivery Area (HSDA) boundaries; 2022 boundary configuration. The HSDAs are a mutually exclusive and exhaustive classification of the land area in BC. HSDAs are contiguous (land area is geographically adjacent) and fit within a geographical hierarchy structure, e.g., cannot violate higher-level geography boundaries Health Authorities (HA).

The spatial representation for a Timber Supply Area or TSA Supply Block: A Timber Supply Area is a designated area established by the Ministry in order to practice sound, integrated, resource management principles to improve the allowable annual cuts. TSAs were originally defined by an established pattern of wood flow from management units to the primary timber-using industries. They are the primary unit for allowable annual cut (AAC) determination. A TSA Supply Block is a designated area within the TSA where the Ministry approves the allowable annual cuts